Jump to content

5 Апреля открытие Victoria x100
ВРЕМЯ ОТКРЫТИЕ 20:00!

Сервер успешно открыт x100!

[FAQ] — Очистика ДНС кеша / Clearing the DNS cache


steve.dog
 Share

Recommended Posts

  • [STAFF L2ANT]

Когда вы работаете в Интернете - пытаясь загрузить любые веб-страницы - часто возникают различные "наложения" - от сообщения "Сервер не найден" до появления вместо веб-страницы какой-то абракадабры. Конечно, большинство этих проблем вызвано временными проблемами с сервером провайдера или хостингом веб-сайта.

Однако часто в таких случаях очистка кэша DNS-разрешения с помощью команды ipconfig /flushdns помогает.

Для этого:
- нажмите Start -> Run... -> Выполнить программу -> cmd -> ОК;
- переключитесь (при необходимости) на английскую раскладку клавиатуры;
- после приглашения системы C:\Documents and Settings\ИмяПользователя> введите ipconfig /flushdns, нажмите Enter;
- кэш DNS-разрешения будет сброшен:

Цитата

makefile
Copy code
C:\Documents and Settings\Admin>ipconfig /flushdns
Настройка протокола IP для Windows
Кэш DNS-разрешения успешно очищен.
C:\Documents and Settings\Admin>


Примечания:
Служба DNS-клиента (Dnscache) должна быть включена.
Эта служба разрешает DNS-имена в адреса для этого компьютера и помещает их в кэш. Если служба остановлена, DNS-имена не могут быть разрешены, и служба каталога не может быть размещена на контроллерах домена Active Directory. Если эта служба запрещена, не удастся запустить какие-либо явно зависимые службы.
Тип запуска (по умолчанию) - Авто.
Исполняемый файл - C:\WINDOWS\System32\svchost.exe -k NetworkService.
Если служба Dnscache не включена, при попытке очистки кэша DNS-разрешения вы получите сообщение DNS resolver cache cannot be cleared: Function execution error.

Как включить службу DNS-клиента:
- нажмите Start -> Settings -> Control Panel -> Administration -> Services;
- в открывшемся окне Службы в списке Службы (локальные) выделите службу клиента DNS;
 - нажмите Start the service.
- Как установить тип запуска DNS-клиента для службы - Auto:

нажмите Start -> Settings -> Control Panel -> Administration -> Services;
- в открывшемся окне Службы в списке Службы (локальные) выделите службу клиента DNS;
- дважды щелкните левой кнопкой мыши, чтобы открыть окно Свойства DNS Client (Локальный компьютер) (или щелкните правой кнопкой мыши, чтобы открыть контекстное меню, из которого выберите Свойства);
- на вкладке Общее в раскрывающемся списке Выберите тип запуска Auto -> ОК;
- закройте окно Службы.
- Если у вас нет времени/лени для очистки кэша DNS-разрешения, скачайте и разархивируйте файл flushdns.zip.
Запустите файл flushdns.bat.

Link to comment
Share on other sites

  • [STAFF L2ANT]

When working on the Internet – when trying to download any web pages - there are often all sorts of "overlays– - from the message The server was not found. It is impossible to display the page before the appearance – instead of a web page - of some gibberish. Of course, most of these problems are caused by temporary problems with the provider's server or the website hoster.

However, often in such cases, clearing the DNS resolver cache with the ipconfig /flushdns command helps.

To do this:
- click Start –> Run... -> Run the program -> cmd -> OK;
- switch (if necessary) the keyboard layout to EN;
- after inviting system C:\Documents and Settings\Username> enter ipconfig /flushdns, click;
- DNS resolver cache will be reset:

C:\Documents and Settings\Admin>ipconfig /flushdns
Configuring the IP Protocol for Windows
DNS resolver cache has been successfully reset.
C:\Documents and Settings\Admin>

Notes
1. The DNS Client service (Dnscache) must be enabled.
This service resolves DNS names to addresses for this computer and places them in the cache. If the service is stopped, DNS names cannot be resolved and the directory service cannot be hosted Active Directorycontrollers of the domain. If this service is not allowed, it will not be possible to start any explicitly dependent services.
The startup type (by default) is Auto.
Executable file – C:\WINDOWS\System32\svchost.exe -k NetworkService.

If the Dnscache service is not enabled, when you try to clear the DNS resolver cache, you will receive a message DNS resolver cache cannot be cleared: Function execution error.

2. How to enable the DNS Client service:
- click Start –> Settings -> Control Panel -> Administration –> Services;
– in the window that opens Services in the Services list (local) highlight the DNS client service;
- click Start the service.

3. How to set the DNS client startup type for the service - Auto:
- click Start –> Settings -> Control Panel -> Administration –> Services;
– in the window that opens Services in the Services list (local) highlight the DNS client service;
- double-click the left mouse button to open the DNS Client (Local Computer) - Properties window (or right-click to open the context menu from which select Properties);
- on the tab General in the drop-down list Select the startup type Auto -> OK;
- close the window Services.

4. If you have no time/laziness to deal with clearing the DNS resolver cache, download and unzip the file flushdns.zip.
Run the flushdns.bat file.

Link to comment
Share on other sites

  • steve.dog changed the title to [FAQ] — Очистика ДНС кеша / Clearing the DNS cache
Guest
This topic is now closed to further replies.
 Share

×
×
  • Create New...